industry news
Subscribe to EE Journal Daily Newsletter

Pentek Provides Software Defined Radio Interface for NeXtRAD Multistatic Radar System

OTTAWA, CANADA CANSEC (CANADA GLOBAL DEFENCE & SECURITY SHOW)─May 31, 2017─Pentek, Inc., NeXtRAD is a dual-band, dual-polarization, multistatic radar system under development at the University of Cape Town (UCT) in collaboration with University College London (UCL). The primary mission of the system is to collect multistatic data of small radar cross-section maritime targets embedded in sea clutter.

NeXtRAD is a multi-sensor network comprised of three stations (or nodes) separated by several hundred meters, all focusing on a common target area. The system requires a usable bandwidth of 50 MHz to achieve a range resolution of three meters. Each node has dual-polarized L- and X-band antennas (IEEE definition) with a 10-degree beamwidth.

This arrangement effectively forms a pair of bistatic radars in combination with a monostatic radar, which means that target data can be simultaneously acquired from three perspectives. This topology has advantages over single-sensor radars. NeXtRAD is a more capable version of NetRAD, a single-frequency multistatic radar developed by UCT and UCL.

“Pentek’s Cobalt® Model 71621 was selected as the SDR interface because it is well suited to the radar’s requirements, providing three A/D converters and a dual-channel 800 MHz D/A converter,” said Mr. Dane du Plessis, member of the system integration team for NeXtRAD.

Initial Testing and Results:  NeXtRAD requires that waveform generation and digitization be fully coherent at each node. To achieve coherency, each node is supplied a very stable 10 MHz reference signal from a local GPS-disciplined oscillator (GPSDO), which is distributed via a frequency distribution unit (FDU) to the Cobalt module and to the receiver exciter (REX). This ensures that there is no phase drift between oscillators in a given node and that the relative phase of oscillators between any two nodes is constant.

The controller software for the Cobalt module was developed using Pentek’s ReadyFlow® software libraries, in conjunction with an arbitrary waveform generator, spectrum analyzer and an oscilloscope. The digitization and waveform generation chains were developed and tested in separate controller programs before fusing these programs into a working source. A simple IF loop-back test, using one of the D/A output channels and a signal splitter, was used for development of digital transceiver before introducing the REX and other subsystems.

The hardware testing configuration, including a frequency distribution unit (FDU), the timing control unit (TCU), the Cobalt module and the receiver exciter (REX), was used to test a low-power bench-top prototype of the active node, using an AWG to supply a rising-edge trigger to the Cobalt module, and signal generators to supply synchronized reference signals to the REX and the Cobalt module.

Using this system, it was possible to detect moving targets by their Doppler shift at close range, such as a moving human target at approximately 75 meters from the transmitter, using a 500 nanosecond pulse with 50 MHz of bandwidth.

Passive nodes are essentially identical to the active node, except the transmitters are not needed. Using virtually the same controlling software for the Cobalt module in the active node, passive nodes can record waveforms at precisely the same moment as in the active node.

“The initial testing of the Cobalt module in the active node demonstrated that the Pentek Model 71621 was well-suited to a pulse-Doppler radar application. With the required additional hardware, the passive nodes can be introduced to the network with minor alterations to code for the active node’s digital transceiver. Overall, the Cobalt module met our requirements for phase stability and bandwidth and it was easily integrated with the existing receiver exciter for the active node,” concluded Mr. Dane du Plessis.

For additional details, go to: http://pentek.com/pipeline/26_2/pipeline26_2.cfm?HID2=HP

About Pentek: Pentek, an ISO 9001:2008 certified company, designs, manufactures and markets innovative COTS and rugged DSP boards and system recorders for commercial, government and military systems, including radar, communications, medical and industrial control applications. Pentek offers powerful VPX, VXS, FMC, XMC, cPCI, PCIe and AMC boards for data acquisition, software radio and digital signal processing featuring Xilinx FPGAs. Pentek’s high-speed real-time recording systems are pre-configured and can be used in the lab or deployed in the field. Pentek equips all boards and recorder products with high-performance I/O including gigabit serial interfaces, powerful software development tools and offers strong DSP software support.

Leave a Reply

featured blogs
Aug 18, 2017
After leaving the title of yesterday's post in German, the obvious place to go for the next stop on the summer of computer museums is Germany. If you ask people which was the first digital computer, the answer tends to vary with the respondent's nationality. Do comp...
Aug 16, 2017
With our last web update, we brought you a major update to our on-site search capabilities, an update to how we serve static webfiles on the website, and a few new content pages for industry standard products. In July, we continued to make improvements to our recently rele...
Aug 09, 2017
Recall for a moment a scene—you’ve probably witnessed something like it at trade shows or on video dozens of times. A robot arm moves purposefully from its rest position. It swoops down on an object—a sphere, say—plucks it up, holds it aloft, replaces it, ...
Aug 03, 2017
Speedcore eFPGAs are embeddable IP that include look-up tables, memories, and DSP building blocks, allowing designers to add a programmable logic fabric to their SoC. The Speedcore IP can be configured to any size as dictated by the end application. The SoC supplier defines t...