industry news
Subscribe Now

STMicroelectronics and Politecnico di Milano Build FASTER 3D Graphics Application using FPGAs

Geneva, December 11, 2014 — STMicroelectronics (NYSE: STM), a global semiconductor leader serving customers across the spectrum of electronics applications, today announced that it had tested and validated an experimental 3D-graphics application based on ray-tracing technology that had been implemented on an ARM®-processor-based test chip attached to a Field-Programmable Gate Array (FPGA). Partially funded by the European Union Seventh Framework Programme (FP7 IC T 287804), the effort for “Facilitating Analysis and Synthesis Technologies For Effective Reconfiguration” (FASTER) was performed as part of a tight R&D cooperation with Politecnico di Milano that also involved Foundation for Research and Technology – Hellas.

FPGAs are special-purpose silicon chips that can be programmed to change their function. These devices can dynamically modify their function during operation to morph between different circuits. Reconfigurable FPGA hardware is often used to deliver greater performance per unit of space, power, and cost, compared with general-purpose central- and graphics-processing units (CPUs and GPUs) for a wide range of embedded applications.

“The Multimedia and Smart Camera markets, in particular, have a high need for added-value functionalities in order to effectively capture their growth potential. A flexible, low-cost system based on reconfigurable hardware can address that need and meet market demands much more effectively than traditional processor-based systems,” said Danilo Pau, Senior Member, Institute of Electrical and Electronics Engineers, and Senior Principal Engineer, Senior Member of the Technical Staff, STMicroelectronics. “The technology developed as part of the FASTER project has the potential to boost computational power per silicon area per power consumption while adding a new dimension to embedded systems capabilities.”

About FASTER

FP7 IC T 287804 FASTER (Facilitating Analysis and Synthesis Technologies for Effective Reconfiguration) is a multi-national research project partially funded by the European Commission’s Seventh Framework Program (FP7) for Research and Technological Development. The commercial partners in the project are: Maxeler Technologies, STMicroelectronics, and Synelixis Solutions. Research & Academic partners are: Chalmers University of Technology, Foundation for Research and Technology – Hellas, Ghent University, Imperial College London, and Politecnico di Milano. The project started on September 1st, 2011 and ran for 3 years. Please visit http://www.fp7-faster.eu for more information.

About STMicroelectronics

ST is a global leader in the semiconductor market serving customers across the spectrum of sense and power technologies and multimedia convergence applications. From energy management and savings to trust and data security, from healthcare and wellness to smart consumer devices, in the home, car and office, at work and at play, ST is found everywhere microelectronics make a positive and innovative contribution to people’s life. By getting more from technology to get more from life, ST stands for life.augmented. In 2013, the Company’s net revenues were $8.08 billion. Further information on ST can be found at www.st.com.

Leave a Reply

featured blogs
May 2, 2024
I'm envisioning what one of these pieces would look like on the wall of my office. It would look awesome!...
Apr 30, 2024
Analog IC design engineers need breakthrough technologies & chip design tools to solve modern challenges; learn more from our analog design panel at SNUG 2024.The post Why Analog Design Challenges Need Breakthrough Technologies appeared first on Chip Design....

featured video

MaxLinear Integrates Analog & Digital Design in One Chip with Cadence 3D Solvers

Sponsored by Cadence Design Systems

MaxLinear has the unique capability of integrating analog and digital design on the same chip. Because of this, the team developed some interesting technology in the communication space. In the optical infrastructure domain, they created the first fully integrated 5nm CMOS PAM4 DSP. All their products solve critical communication and high-frequency analysis challenges.

Learn more about how MaxLinear is using Cadence’s Clarity 3D Solver and EMX Planar 3D Solver in their design process.

featured paper

Designing Robust 5G Power Amplifiers for the Real World

Sponsored by Keysight

Simulating 5G power amplifier (PA) designs at the component and system levels with authentic modulation and high-fidelity behavioral models increases predictability, lowers risk, and shrinks schedules. Simulation software enables multi-technology layout and multi-domain analysis, evaluating the impacts of 5G PA design choices while delivering accurate results in a single virtual workspace. This application note delves into how authentic modulation enhances predictability and performance in 5G millimeter-wave systems.

Download now to revolutionize your design process.

featured chalk talk

Achieving High Power Density with IGBT and SiC Power Modules
Sponsored by Mouser Electronics and Infineon
Recent trends in the inverter market have made high power density, scalability, and ease of assembly more important than ever before. In this episode of Chalk Talk, Amelia Dalton and Abraham Markose from Infineon examine how Easy & Econo power modules from Infineon can help solve common inverter design requirements. They explore the benefits and construction of these modules and how you can take advantage of them in your next design.
May 19, 2023
38,471 views