industry news
Subscribe Now

NREL Invites Robots To Help Make Wind Turbine Blades

Research Enables Successful Automation in Post-Molding Manufacturing Operations

Golden, CO, May 02, 2024 (GLOBE NEWSWIRE) — Researchers at the U.S. Department of Energy’s National Renewable Energy Laboratory (NREL) have successfully leveraged robotic assistance in the manufacture of wind turbine blades, allowing for the elimination of difficult working conditions for humans and the potential to improve the consistency of the product.

Although robots have been used by the wind energy industry to paint and polish blades, automation has not been widely adopted. Research at the laboratory demonstrates the ability of a robot to trim, grind, and sand blades. Those necessary steps occur after the two sides of the blade are made using a mold and then bonded together.

“I would consider it a success,” said Hunter Huth, a robotics engineer at NREL and lead author of a newly published paper detailing the work. “Not everything operated as well as we wanted it to, but we learned all the lessons we think we need to make it meet or exceed our expectations.”

The paper, “Toolpath Generation for Automated Wind Turbine Blade Finishing Operations,” appears in the journal Wind Energy. The coauthors, all from NREL, are Casey Nichols, Scott Lambert, Petr Sindler, Derek Berry, David Barnes, Ryan Beach, and David Snowberg.

The post-molding operations to manufacture wind turbine blades require workers to perch on scaffolding and wear protective suits including respiratory gear. Automation, the researchers noted, will boost employee safety and well-being and help manufacturers retain skilled labor.

“This work is critical to enable significant U.S.-based blade manufacturing for the domestic wind turbine market,” said Daniel Laird, director of the National Wind Technology Center at NREL. “Though it may not be obvious, automating some of the labor in blade manufacture can lead to more U.S. jobs because it improves the economics of domestic blades versus imported blades.”

“The motive of this research was to develop automation methods that could be used to make domestically manufactured blades cost competitive globally,” Huth said. “Currently offshore blades are not produced in the U.S. due to high labor rates. The finishing process is very labor intensive and has a high job-turnover rate due to the harsh nature of the work. By automating the finishing process, domestic offshore blade manufacturing can become more economically viable.”

The research was conducted at the Composites Manufacturing Education and Technology (CoMET) facility at NREL’s Flatirons Campus. The robot worked on a 5-meter-long blade segment. Wind turbine blades are considerably longer, but because they bend and deflect under their own weight, a robot would have to be programmed to work on the bigger blades section by section.

The researchers used a series of scans to create a 3D representation of the position of the blade and to identify precisely the front and rear sections of the airfoil—a special shape of the blade that helps the air flow smoothly over the blade. From there, the team programmed the robot to perform a series of tasks, after which it was judged on accuracy and speed. The researchers found areas for improvement, particularly when it came to grinding. The robot ground down too much in some parts of the blade and not enough in others.

“As we’ve gone through this research, we’ve been moving the goal posts for what this system needs to do to be effective,” Huth said.

The robot was not compared to how a human would perform the same functions.

Huth said an automated system would provide consistency in blade manufacturing that is not possible when humans are doing all the work. He also said a robot would be able to use “tougher, more aggressive abrasives” than a human could tolerate.

The U.S. Department of Energy’s Advanced Materials and Manufacturing Technologies Office funded the research.

NREL is the U.S. Department of Energy’s primary national laboratory for renewable energy and energy efficiency research and development. NREL is operated for DOE by the Alliance for Sustainable Energy LLC.

Leave a Reply

featured blogs
May 8, 2024
Learn how artificial intelligence of things (AIoT) applications at the edge rely on TSMC's N12e manufacturing processes and specialized semiconductor IP.The post How Synopsys IP and TSMC’s N12e Process are Driving AIoT appeared first on Chip Design....
May 2, 2024
I'm envisioning what one of these pieces would look like on the wall of my office. It would look awesome!...

featured video

Introducing Altera® Agilex 5 FPGAs and SoCs

Sponsored by Intel

Learn about the Altera Agilex 5 FPGA Family for tomorrow’s edge intelligent applications.

To learn more about Agilex 5 visit: Agilex™ 5 FPGA and SoC FPGA Product Overview

featured paper

Achieve Greater Design Flexibility and Reduce Costs with Chiplets

Sponsored by Keysight

Chiplets are a new way to build a system-on-chips (SoCs) to improve yields and reduce costs. It partitions the chip into discrete elements and connects them with a standardized interface, enabling designers to meet performance, efficiency, power, size, and cost challenges in the 5 / 6G, artificial intelligence (AI), and virtual reality (VR) era. This white paper will discuss the shift to chiplet adoption and Keysight EDA's implementation of the communication standard (UCIe) into the Keysight Advanced Design System (ADS).

Dive into the technical details – download now.

featured chalk talk

Achieving Reliable Wireless IoT
Wireless connectivity is one of the most important aspects of any IoT design. In this episode of Chalk Talk, Amelia Dalton and Brandon Oakes from CEL discuss the best practices for achieving reliable wireless connectivity for IoT. They examine the challenges of IoT wireless connectivity, the factors engineers should keep in mind when choosing a wireless solution, and how you can utilize CEL wireless connectivity technologies in your next design.
Nov 28, 2023
23,150 views