editor's blog
Subscribe Now

MEMS Laser Probing

I saw an announcement about a new MEMS diagnostic instrument, the M150 from Ardic. It uses a laser to measure the frequency response of a MEMS element. Sounds simple enough. Or it did until I started thinking more about it. After all, lasers require line of sight. And most MEMS elements are far out of sight. And if you bring them into sight, then you may have changed the environment (air instead of vacuum or controlled gas, microphone packaging and cavities, etc.) So how does that affect the measurement? You can read the best boss laser reviews online to choose one for your business projects.

I had an interesting chat with founder and CEO Edward Chyau to get some perspective on the tool. First, the main use cases: this is typically used either to verify a design early on, for occasional production monitoring, or for diagnosing failed units. So it’s not a high-volume in-line production system. It’s set up to handle dice, although they have had requests for a unit that could handle 6” wafers. (In theory, on a wafer, neighboring dice could interact since they’re mechanically connected, but he said that the actual element movements are so small that by the time their vibrations reached the neighboring die, it would have attenuated to a negligible level.)

And yes, the moving element must be visible. An InvenSense gyro, for example, would need to have its capping ASIC removed to take a measurement. So there will be some difference between the elements behavior under the laser and its behavior in the wild. He says that the tests being run look for significant resonances within the region of interest, indicating that some mechanical element has a resonant mode, due to a design error or a production defect, that can interfere with normal operation. Those modes might shift frequency a little due to depackaging, but not a lot.

So, for example, if a microphone diaphragm exhibited a resonance at 1 MHz, then it wouldn’t be an issue. But if your window was up to 50 kHz and it had a 55 kHz mode, you’d want to pay attention even though it’s nominally outside the window.

It might be possible to anticipate any such shifts at design time. If design simulations were done assuming a vacuum, for example, then it would be possible to redo the simulations without a vacuum to establish a baseline expected behavior for laser probing. That could help set expectations for any change in behavior for correlation if that were a concern.

I also wondered if the laser itself would heat the element during the measurement, changing the performance as it heated. He said that the laser is low-power, like that on a CD-ROM drive, so no noticeable heating should occur during the 60-second scan.

That scan is part of what differentiates this unit from existing devices. Current technology uses laser Doppler interferometry, and it’s largely targeted at the academic environment with relatively high cost and a long learning curve. And a measurement can take 1-2 hours, with reasonably fussy setup.

By contrast, the Ardic system uses astigmatic detection, also used in their atomic-force microscope (AFM) tools. This gives them particularly good z-axis resolution, and they can scan from 1 Hz to 4.2 MHz in 60 seconds. Users often simply run that entire range even if they only need a subset just because it goes so fast.

I also asked whether this technique could apply down to the NEMS range, where quantum effects start to matter. And, in fact, here you’re dealing with features below the visible wavelength. So getting a laser focused that small and capturing the echo isn’t really feasible.

He said that you would likely need to take a more indirect approach. For example, you might have a MEMS-scale cantilever that acts as an atomic-force probe on the NEMS element. It doesn’t actually make contact (although I suppose that, on an atomic scale, where most of the atom is open space, “contact” is not such a clear concept); it just comes within Van der Waals force range. This allows the cantilever to track the motion of the NEMS element; the laser can then be used to measure the cantilever.

But, of course, the cantilever would have its own resonant modes, so you’d have to measure the cantilever first so that you could subtract its behavior out of the combined signal to isolate the NEMS element signal. This hasn’t been done yet, but he saw it as the kind of approach that would be required.

You can read more in their announcement.

Leave a Reply

featured blogs
Mar 28, 2024
The difference between Olympic glory and missing out on the podium is often measured in mere fractions of a second, highlighting the pivotal role of timing in sports. But what's the chronometric secret to those photo finishes and record-breaking feats? In this comprehens...
Mar 26, 2024
Learn how GPU acceleration impacts digital chip design implementation, expanding beyond chip simulation to fulfill compute demands of the RTL-to-GDSII process.The post Can GPUs Accelerate Digital Design Implementation? appeared first on Chip Design....
Mar 21, 2024
The awesome thing about these machines is that you are limited only by your imagination, and I've got a GREAT imagination....

featured video

We are Altera. We are for the innovators.

Sponsored by Intel

Today we embark on an exciting journey as we transition to Altera, an Intel Company. In a world of endless opportunities and challenges, we are here to provide the flexibility needed by our ecosystem of customers and partners to pioneer and accelerate innovation. As we leap into the future, we are committed to providing easy-to-design and deploy leadership programmable solutions to innovators to unlock extraordinary possibilities for everyone on the planet.

To learn more about Altera visit: http://intel.com/altera

featured chalk talk

USB Power Delivery: Power for Portable (and Other) Products
Sponsored by Mouser Electronics and Bel
USB Type C power delivery was created to standardize medium and higher levels of power delivery but it also can support negotiations for multiple output voltage levels and is backward compatible with previous versions of USB. In this episode of Chalk Talk, Amelia Dalton and Bruce Rose from Bel/CUI Inc. explore the benefits of USB Type C power delivery, the specific communications protocol of USB Type C power delivery, and examine why USB Type C power supplies and connectors are the way of the future for consumer electronics.
Oct 2, 2023
23,151 views