fresh bytes
Subscribe Now

Photographer catches his camera drone moments before it crash-lands in the ocean

drone1.jpg

Perth, Australia-based photographer Ryan Chatfield was recording aerial footage of Perth’s City Beach when his brand-new camera drone ran low on batteries and began an automatic descent toward the waves below. What followed was a mad 100-yard dash that required Chatfield to clamber over a rock jetty and into the ocean. He managed to catch the drone when it was about a foot from the water. Then he endured a good flogging by a wave as he climbed back up the jetty with his (intact) drone. All of this was recorded by the drone’s camera.
via Laughing Squid

Continue reading 

Image: Ryan Chatfield

2 thoughts on “Photographer catches his camera drone moments before it crash-lands in the ocean”

  1. I’m unsure. Some things make me suspect it could be staged:

    – The camera is conveniently pointed at the guy the whole time. That would make it much easier if someone else were flying it to have it arrive at exactly the right time for him to catch it.
    – He arrives without his radio gear – did he just dump it in the sand on the beach and start running?
    – He seemed VERY fast to diagnose what was happening (low voltage auto-land) and make the decision to run to try and catch it. He also seemed to take pretty much the optimal path over the jetty to get there – and it would have been a tiny dot in the sky from where he was originally standing.
    – The camera is manually tilted back up to “level” after the descent starts. Who did that and why? It did make for a better viewing angle for the rescue.
    – The first time we see the props, they have stopped. It’s unclear when/why they would have stopped after he caught it. We don’t see him disconnect the power, and on the audio we hear the waves crashing and him talking, but never the sound of the motors.
    – He conveniently keeps the camera pointed at himself while he climbs back up out of the water – and keeps it level.
    …lots of very convenient elements.

    On the other hand, the whole thing is plausible:
    – the DJI flight controllers DO have a low-voltage mode that causes them to descend and auto land if the battery gets too low.
    – the quad doesn’t yaw after it starts down (correct for auto-land)
    – the descent seems very steady (also correct for auto-land).

    Anybody else got any insights?

Leave a Reply

featured blogs
Apr 16, 2024
In today's semiconductor era, every minute, you always look for the opportunity to enhance your skills and learning growth and want to keep up to date with the technology. This could mean you would also like to get hold of the small concepts behind the complex chip desig...
Apr 11, 2024
See how Achronix used our physical verification tools to accelerate the SoC design and verification flow, boosting chip design productivity w/ cloud-based EDA.The post Achronix Achieves 5X Faster Physical Verification for Full SoC Within Budget with Synopsys Cloud appeared ...
Mar 30, 2024
Join me on a brief stream-of-consciousness tour to see what it's like to live inside (what I laughingly call) my mind...

featured video

How MediaTek Optimizes SI Design with Cadence Optimality Explorer and Clarity 3D Solver

Sponsored by Cadence Design Systems

In the era of 5G/6G communication, signal integrity (SI) design considerations are important in high-speed interface design. MediaTek’s design process usually relies on human intuition, but with Cadence’s Optimality Intelligent System Explorer and Clarity 3D Solver, they’ve increased design productivity by 75X. The Optimality Explorer’s AI technology not only improves productivity, but also provides helpful insights and answers.

Learn how MediaTek uses Cadence tools in SI design

featured chalk talk

Electrical Connectors for Hermetically Sealed Applications
Sponsored by Mouser Electronics and Bel
Many hermetic chambers today require electrical pathways to provide internal equipment with power, data or signals, or to receive data and signals from equipment within the chamber. In this episode of Chalk Talk, Amelia Dalton and Brad Taras from Cinch Connectivity Solutions explore the role that seals and connectors play in the performance of hermetic chambers. They examine the methodologies to determine hermetic seal leaks, the benefits of epoxy hermetic seals, and how Cinch Connectivity’s epoxy-based seals and hermetic connectors can add value to your next design.
Aug 22, 2023
28,284 views